North Dakota Fishing and Hunting Forum banner

12GA FH to 700HE-- Hairy rifle/shotguns.

86K views 122 replies 3 participants last post by  hubel585 
#1 ·
Just visiting here to tell about our
12GA From Hell videos on Youtube, and a
little info about our ongoing work. If you
have questions please ask. Here is pic of our
12GA FH case on the right. We made cases by
putting 12ga size rim on bmg brass. Another
case made from same is my belted 700HE,
more powerful, capable of muzzle energys
over 20,000 ft lbs...Ed Hubel

The videos are called--
Grandpa's First Shot-



Grandpa's Cannon-



 
See less See more
2 1
#2 ·
I'm back visiting to fill you folks in on our 12ga FH, 700HE, and other work and research
that I and others have done.. problems back when and finally finding some of the sites.
First is picture of the Savage 210 I had the first 12ga FH in with heavy barrel. 2nd pic
is the 1887 levergun I put heavy barrel on for the case.3rd is Enfield and
Savage 210 with my 700H 3.25" belted case.







Next showing an 8ga we built using a thick barrel SB2 NEF
10ga gun. We bored out the barrel and rechambered for the 3.3" long 8ga case.
The cases are the 8ga heavy duty plastic kiln gun cases we swage down to remove
the belt step. She gets a 900gr over 2000 fps.
Here is picture of the breach of 8ga FH NEF with
case in it, to show that the gun is strong enough
for 8ga. Has 30" effective 8ga size. 832" bore, barrel
length, and the internal expansion step at muzzle
for the ports that stops muzzle climb and reduces
recoil. Which along with thick pad and thumbhole
stock makes for easy shooting.Ed





Next is picture of my 12GA FH in the NEF with a barrel extension added.
I never was happy with short barrel and now I can test velocities in long one.



Next is a NEF with a mono-blocked 585 cal barrel in it for my 585HE belted case.
This case will outrun the trex , and is simpler to resize and load. I also put it in
a CBC singleshot action by mono-blocking in a 585 barrel. To do this I cut
off barrel about 3" ahead of the breach, ream and thread it and thread 585 barrel to go in.
Makes nice inexpensive singleshot elephant gun out of C&R type gun.





Next is the new RMC PH super large action that I put my 585HE, 585HSM and 700HE into.
In front the 585HSM with port lengthened , in back the 700H 3.25" one. I have barrels
in my 585HE and long 700HE to switch to.



Next is the Hubel Falling Block, HFB, in 4bore and 8ga. This falling block uses
a simple open hammer setup and all sises use same hammer, trigger, lever,etc.They
are just different widths for barrel and case size. This falling block is a different
concept, with action and barrel in a one piece stock. The 4ga is 1"bore and uses
cases we made from 20mm brass and they are same as the 4ga turned cases that
Ken Owen had made for the 4bore doubles he made. The 8ga uses the heavy plastic
kiln case we swaged the belt down on.And brass cases if we get them made.
I have a huge amount more info and pictures, about our big bore research and work.Ed



 
#3 ·
Here are pictures, huge variety of 12ga slugs and saboted slugs.
First a 600 NE slug in in 12ga wadcup... 2nd The US-S slug
along with others.3rd a Jacketed 730gr and a hard cast, heat treated
600gr, full bore slugs, 4th a sabot with hardcast .504"
diameter slug, 5th other sabots, 6th brass turned slugs
and there are many others.Ed











 
#4 ·
Here are some pictures of our various cases, how they are made,
comparing sizes, showing them loaded, empty, and sectioned.

First is a bunch of our biggest ones. In order- 2bore, 4bore, 8ga, 10ga,
12ga FH , 700HE, 700H 3.25, with 30-06 for comparison.



2nd-- showing the process of making our 12ga FH from BMG brass
by putting on a 12ga rim piece..



3rd- showing how we make our 700HE belted case from BMG brass
by putting on a belt them expanding case to 700cal.



4th- Showing our 700HE with 700 H 3.25 along with bullets.



5th- showing our 4bore case and the 20mm we make it from
and jacketed 4bore slugs..



6th-A regular brass 12ga case and our 12ga FH



7th-Center 585HE belted case and 700H 3.25, 458 for comparison.



8th- Our 700HE case, that was fired 25 times, sectioned to show
the strength and the lack of case stretching. Over half the loads were
full power, max loads.



9th- An 8ga plastic kiln case, sectioned to show its great strength.
I can fire these 4 times with fairly strong loads without sizing.



10th- A comparison of length for my 585HE and a 505 Gibbs,
showing that my super 585HE can fit in many guns that the
Gibbs goes into, like PH, Enfield, CZ550, Big Ruger 77,
as well as any falling block or break action, double, single, o/u.



11th- Our 700H 3.25, in a MRC PH, bolt action, the first one
from the factory, feeding from the single stack
magazine we built. Gun has thumbhole stock
and 700cal rifled barrel. Ed

 
#5 ·
In the early days; in my Greener's book he states that
gun with a rifled choke section of the barrel, called
12ga paradox shotgun/rifles, with slugs, heavier powder
charges than shot loads, could hold what amounted to
about 5 inch pattern at 100 yds.

And still had 1800 ft lbs energy at 100yds.
And that is with guns with lighter, weaker barrels
than we have today, so our work is a good extension
of what the early big bore guys did.

And then the 4bore for guys liking a big challenge, 3rd picture...Ed





 
#6 ·
Thanks to rattler on 24hr forum for the old time pictures,
above, and the guys really like them. Quite interesting.

Many have success with all kinds of high-power slug designs and
with extra power, have pushed the reliable range of 12ga slugs/bullets
from 75 yds to over a 150 yds. ...Here is picture from a 1926
Manton catalog showing, 1st picture, many brass case old time slug loads.
Notice the 20bore and 12 bore ones with pointed slugs, seems
as ideas to hotrod 20s and 12s are old hat, not as strong as 12ga FH ....
Both Pictures below from lancaster and CptCurl on Nitroexpress.

2nd picture are saboted slugs, called the SAGA, from Spain,
next to a Brenekke on the right..AS far as I can find only
sold so far as loaded rounds. They look great to reload with
if ever available..

3rd picture is from my Greener book, of double 8ga elephant guns.Ed





 
#7 ·
You can see various 4bore, 8bore, etc shooting videos on Youtube.
Some of the guns will be nice old timers like the pictures.

And in the vein of old time gun actions, of which are various falling
blocks, we like them also for the hairy big bores, like the 8bore and
4bore ones we made over the years, that are pictured above.
Following are 3 pictures of various parts and processes of making the
action, using easy to get small parts, lever, trigger, hammer, etc,
and the action block, breach block from steel blocks in 1st pic.

Last 2 pictures are the FBW brand falling blocks, one which is the
Model L that we adapted to the one piece stock and the other is the
smaller Model S with regular two piece stock. Both are set up with
my 585HE. I can run full pressure in the 585.

The Model L, I can switch to a 20ga barrel, 600NE barrel,
and my 700HE using moderate loads. Last pic is Model L with
thumb hole stock, and my 585HE case in the action..Ed











 
#8 ·
Here is picture of an early falling block for big bores
called the Field I think. Looks like some other
side levers, looks like lever works forward.

And speaking of falling blocks next picture is the
start or 'fixins' so to speak for the next step
up, for my 2bore. Same design as the 4 and 8
bores only wider.

I am now getting 2.25" OD barrel reamed
out to the two bore size.
And a square hole for breach block done
in that hunk of 4130 steel.

Other experimenting, a while back, when I made
my 585 Short HE from Gibbs cases, I also made a
620 Short HE from Nyati case, of the same design,
IE, head spacing on the mouth and extractor.
Using 600NE .620" diameter bullet and 2.7" long case.
Case could be shorter or longer like the 585 one.
Didn't do much with it as its sides were very straight
only .010" taper of both sides together. Whereas the
585 Short HE had .027" total taper both sides. And any
Nyati brass I got, went to make my 585HE cases..Ed





 
#9 ·
Here is picture of my 585HSM and some other cases.
It is made from reworked bmg brass, and case 3.6" long.
Got it in a PH in the 2nd picture. 3rd picture a supply
of 585 or 24 ga if you want, that are hard cast and
lubes and they take the real high sped ok...ED







Here is picture of Brett Savage 210 he has setup.
It has a 3.5" 12ga chamber in a heavy 27" Pacnor barrel,
oversize recoil pad, and he put in a Knoxx
spring/cam recoil absorbing butt plate in the hollow
Savage plastic stock. It is shown without the boot
so you can see how it is in the butt.
He hasn't weighted the gun with anything else and
it shoots comfortable, even off the bench with loads that get
a 500gr slug in a BPI sabot to 3000 fps. He gets this speed
with BPI sabot and 500 gr in 3.5" plastic cases. He also can use
3.5" RMC brass cases...Ed



New super strong 12ga bolt gun is out, Savage 212, taking
over for the 210. You know I did my first 12ga FH in a 210 and
have posted that sometime I'd like to get a thicker walled
receiver built to have more strength and safety.
Well Savage helped us out a little
Its reciever is 1.5" diameter, where the 210 was 1.36" dia.
I has a large .900" diameter bolt, where the 210 had regular
110 bolt inside bolt carrier. It has a fitted bolt head like 210
and other Savage 110-116 rifles. Only its bolt head has two lugs
where the 210 had 3 lugs. Its two lugs about 90% strength as
the 210s 3 lugs.Its about 12% stronger lugs than Enfield and
Ruger 77. ED
 
#10 ·
Many are interested in 12ga FH set up in doubles.
Able to take higher pressures than thin shot barrels.
Like the pressures in NE cases that are put in doubles
that are similiar to big shot gun frames.
Rob on the AR Forum who's idea the 12GA FH originally was,
is doing one by putting heavy one on a large 10ga frame.
He is mono-blocking in heavy 12ga rifles barrels into the
breach section of the 10ga.He has to make and install ribs,
quarter rib, etc, so it will look like a big double rifle.
5th picture is of bolt action a guy made for big cases,
beautuful work and very strong.6th picture is a bolt gun
a guy on gunsmithing forum built for 8ga. Uses top power
loads that the heavy duty 8ga plastic cases can do.Ed











 
#11 ·
More history of firsts, in our 12ga FH and big bore work.

First picture is Rob's 50BMG size falling block, that was the
first gun that the 12ga FH case was chambered in.
It is a modern Borchardt and can take full rifle pressures.
With this gun Rob was able to get 1000gr 12ga solid
slug to 3000 fps. The 2nd gun to have this case was
my Savage 210 pictured earlier.

Second picture is the first NEF 12ga Ultra that we put
the first 12ga fH case in. I only had to lengthen chamber.
The same gun now has long barrel and thumbhole stock.

Third picture is first NEF 10ga heavy barrel that we put
the 10ga FH in. Gun came with long 30" heavy barrel.

Fourth picture is the first 8ga test gun we built using the
super strong 8ga kiln cases with the belt step swaged
down. It is an Enfield that we reamed out to take the
case, like the 12ga Mauser 12ga conversions were done.
And we added extra rear bolt lugs for strength.

Fifth picture is the 1st gun my 700H 3.25 was put in.
It is and Enfield and gets 1000gr bullet 2100 fps.
Sixth picture is the first my 585HE was put into.











 
#12 ·
First is picture sectioned Explora case and slug, showing how
they kept weight down so that it could be stepped up in
speed in older doubles, with just short rifling section at muzzle,
that didn't have real heavy barrels. Second picture from Greener
book here, is of older 4 and 8 gauges.

Third picture shows steps of making 4bore case, one inch bore,
from 20mm. 2nd in picture is case with base turned and swaged
to size which leaves base smaller than rim, for rimmed case.
Then 3rd case has top expanded to take 1" diameter slug.
last shows the thickness and strength of finished case.

Testing factory 20ga Hastings sabot slug 3.5" hotrod loads, and
reloaded with 20ga SPW identical slugs, 390gr, goes about 2200
from 30" heavy barrel. Load was 75gr of 4759.
Factory is about 1900. For regular modern barrels you could
do with 65 gr and get about 2000.Ed





 
#13 ·
Some info about our slower powder reloads in plastic and
brass cases with shotgun primers for modern 12ga guns.
I now prefer the IMR 4759 over 4227 as we have had
some delayed firing problems when the loaded cases get
real cold with 4227..And with slower powder loads use
magnum primers.

A side note,in same vein, you know I now use FED239
mag primers in my 8ga and 4ga, but we find they they really
solve the real cold gun, ignition problems, in muzzle loaders
using black powder substitutes, with shotgun primer
inline guns. We tested 50cal and a primer sold especially
for ML when fired,no powder, only saw a tip of the flame
out the barrel, a FED209 mag about 4" flame, buta Fed 239
Mag primer about a foot of flame.

Some more info from the old days, here is picture of
a variety of slugs being promoted and used a century ago.
And 2nd picture Paradox cases old and new.Bottom one is a
modern version sold by H&H for slug hunters.Ed



 
#14 ·
We are always looking for way to shoot 8 and 10s
using easy to get components,cheap, without buying
loaded rounds for big bucks, if available at all.

In 8ga falling block, plastic got 930gr hollowbase
slug to 2300, It is a slug for 10 ga that we expanded
base a little to fit tight in 8ga wadcup. On the left in
picture. At 30 yds 3" group. Just with open sight,
About like the 10ga sight bead. There is enough hollow in
the base it flies pretty good from 8ga smooth barrel.

Along same line, in my 10ga 32" smooth bull barrel with a
750 gr .69cal hollowbase Dixie MZ slug in VP100
10ga wadcup about same speed and same accuracy.
Nice to just get a box of slugs that is in stock,
and a 2cent cent wadcup and Fed 3.5" 10ga plastic cases
and be shooting cheap.And the cases roll crimp nice
down to these slugs.

And also the hotrod 20 ga 3.5" Hastings factory loads in
a smooth barrel moderate weight 20ga shoots about
same accuracy even though they say for rifled, but that
SPW slug/wad combo has enough plastic/seal on the back
and that it shoots like a Brenekke. The new 28ga Brenekkes
out of 28ga NEF modified choke barrel shoots same at 30yds.
Scoped guns and good eyes would shrink groups.Ed

 
#15 ·
A different, interesting style, of 12ga slug, from Russia.
First picture loaded round, in plastic, roll crimped.
Second, two types of slugs they have on the same base.
Base for rifled barrel, little smaller diameter than the front.
Looks like the roll crimp locks against
the edge of the base. Neat idea, and it could have a
flat meplat slug on the front of the base like
the US-S brass slugs fron Greece are on the
plastic bases that I have here. They must use a crimping
die with a deep hollow up in the middle. We have thought
of taking a roll crimper and putting a deeper recess
in middle to load longer nose slugs further out so as to
have more room for our slower powders.ED



 
#16 ·
Here is picture of 4 long cases of
RIP's on the AR forum.
Top being a Rocky Mtn Cartridge
3.5" turned brass 20ga. In 20ga
getting these and lengthening chambers
allows use of the 3.5" 20ga plastic also.
Some factory guns are 3.5"

Next a RMC 3.5" turned brass 12ga.
Chambered for these you can use
3.5" 12ga plastic also.Some guns are
3.5" from the factory.

3rd down our 3.85" 12ga FH we made from BMG brass.
Bottom a RMC 3.85" turned brass 12ga FH case.



Next picture shows one of the old ways they locked slugs
into paper cases. Many old slugs had a wide deep groove
which made it possible to crimp that way.You can
see one of those slugs in the picture.



Testing 490gr 12ga full bore Lee style slugs in 3.5"
plastic at 2200. Works in the long barrel rifled NEF and
the Khan 12ga 3.5" auto smooth bore.

In same guns the 570gr US-S brass slug with
locked on base at 1900 in 3.5" plastic worked also.
It is great to see a smoothbore slug like the US-S
that is as accurate as fullbore slugs from
rifled barrels.Maybe they will be imported soon
from European Cartridge.Ed
 
#17 ·
Here are couple more pictures of longer bullets
in sabots, loaded in plastic cases, with the
roll crimp down against the sabot. Both are
ideas tested by European Cartridge in Greece,
who make the US-S slugs. Both longer bullets
pictured have the locked on base that their
other US-S slugs have, for smooth bore accuracy.
2nd picture shows a deep hollow roll crimper
for doing slugs like these.Ed



 
#18 ·
This picture of an RC4 brand slug I see is available
down under. It has locked base like Brenekke.
And locked on without discarding petals, like US-S.

And 2nd picture is a group fired with RC4 slugs
by fellow on NitroExpress forums from
double 12ga, 2 left and 2 rights at 25yds.
This shows the posibilities of smoothbores,
rather than not trying to perfect them.

3rd picture is a discarding sabot base, and with
four discarding sabot carriers, with centered
penetrating solid bullet, from France.Ed





 
#19 ·
Some more slug and sabot ideas folks are doing.

First is a long pointed slug with locked on base,
It goes to target with base,can work smoothbore.



Second is picture of Hexolit sabot base slug
with petals expanded, sure would make bad wound.



Third shows a variety of Gualandi slugs you can
get for reloading, and we're finding that these
locked base slugs, Brenekke/USS style slugs, are
giving good accuracy in smooth barrels which can
save when doing heavy barrels.Weights shown in
grams, get our weights in grains multiply by 15.4..Ed

 
#20 ·
Here are some more sabot/slug and loading concepts.

First is Alcan 2.75" paper case with Dixie 600gr slug,
with the side of the case crimped into the relief/lube
groove of the Dixie slug.The groove in the Dixie isn't
quite as deep as the groove in the Fosbury slug shown
in earlier post, but still seems to crimp fairly tight.



Next are various slugs in 12ga REM sabots that take
57 cal slugs and bullets.Those sabots are from the REM
Accutip loadings. In picture you can see one of the
REM 385gr jkt bullets they use. Also is sabot
with 20ga cast Lyman. On right sabot with hardcast 585 cal
640gr lead bullet, the ones I use in my 585HE wildcat
case. I sized it down a little, perfect fit.
Also the .575 cal Dixie Gunworks lead slugs will do.

Also shown is a long pointed 55 Boys bullet in one,
fairly tight fit.We cut back .3" of bullet off so it
fit for length in sabot and is 750gr.



Third are 3.5" brass and plastic with the REM sabot and
the 750gr pointed slugs in them.In all the sabot work we
and others have done, trying to get accuracy and high
speeds together, maybe there is such a thing as too
much plastic. IE, sabots too thick on the sides if doing
50cal or smaller in 12ga sabots, for heavier slugs
at high speeds. Thinner sides may discard more evenly at
the greater pressures and violence of high speeds.
Thin sides may have less give so that sabot grips slug
better to impart spin in rifled use. Example in
smoothbore use is the USS slugs, where the brass slug
is .629" with thin discarding petals that have proven to
be very accurate. And with both reasonable priced sabot
offerings the last few years being undersize, accuracy
problems, etc, maybe time to try something else.

Got to find whole bunch of these sabots. Are these pictured
12ga REMs the only 58cal ones around? I can't find others,
and maybe we can find where these are made. As I have
huge numbers of the 585 slugs, which by the way I think
is best hunting combination, without extremely heavy slugs
which suffer for the speeds needed for longer range use.
It is hard lead, good for big game.And my guy can make many,
many more if needed whether for 585HE rifles
or in sabots if we can find some.ED

 
#21 ·
Some more sabot and slug ideas, discarding types
and locked on base types.

First picture of 20ga Buckhamer pulled apart. The bunch
I have were pulled apart, the slug won't lock back in
tight, into the base.



Second is various 20ga sabot/slug ideas some using
buckhammer sabot bases that a bunch of 458 cal lead
slugs and jackted slugs I have, lock into real tight.
The 458 lead ones are 400gr, jkt are 350gr.

And I got some empty SPW 20 gauge sabots, and 20ga
Buckhammer slugs lock into them real tight.I have
many of these slugs. These slugs are 440gr.

Also is 3" 20ga FED factory sabot shell and one of
discarding sabots out of the case. Also a 3.5" 20ga
Hastings 3.5" load with black locked on base sabot,
and sabots out of the case and couple 20 brass
3.5" RMC cases.



Next is variety of 12ga sabots with 50cal slugs
in them.2 white and the pink sabot are FED, The black
is Hornady, With a 50cal long bullet .
The grey, is a BPI with .504" cast 440gr slug.
I wish the BPI was full size like the others
and fit rifled barrels tight for accuracy.........



Last 12ga SPWs from Slug-R-US(30 cents ea) with various
50 cal slugs locked in tight, and shown with one out of
a factory load, the dark colored one. 50cal 385gr
Great Plains ML slugs lock in perfect for a lighter
loading. Other ML slugs will do and a few of
the Dixie Gunworks 50cal slugs lock in also...Ed

 
#22 ·
Some more slug setups and ideas.

First is USS brand sabot that European cartridge has, without
locked base, a discarding 12ga sabot, with .629" brass slug.
It is as accurate in rifled barrel as its locked on base
counterpart, in smooth barrels. Up to 750 gr brass slug
I tested. 3 shots in an inch, 30yds.
Shown with BPI powder cup seals.



2nd is the USS slugs with locked on base for comparison.
With corresponding length cases they were designed for.



3rd are heavy solid tungsten slugs, the smaller .580" cal and
1200gr, the bigger ones .660" cal and 2200 gr.
A guy in Southern MI made a few for me to check out. Now these
too hard to fire fullbore, damage rifling, must be in plastic.
These are just what the super heavy slug guys might like.



4th is a 1000gr 58cal tungsten slug in a 12ga REM style
58cal sabot. Notice how short it is for being super heavy.

 
#23 ·
Here is some more older cartridges and ideas.
First is a fellows collection of older brass cases.
They look like Berdan primed. Run from
36ga to 12ga, big one on right is flare cartridge.



Second is a paper case clad with
thin brass nearly to the top.



Third is picture of paper case crimped into
the side of a slug with shallow grooves.I did one
pictured above with a Dixie slug.



Some experimenting with 12ga discarding style sabot idea
that takes 58cal slugs/bullets.I pictured them above.
A fullbore,bore fitting sabot that takes 575-580 cal
slugs or bullets, cast or jacketed.

For reloaders to use, and not undersize ones
that have been available, for reloading guys. That
the guys haven't been able to get speed and accuracy
at the same time. These sabots are super accurate in
most tests, in factory Remington sabot loads. Much
more so than the undersize sabots reloaders have
had to work with.

I tested with the 440 gr .575cal hollowbase
Dixie Gunworks # BA-1103 lead slug and 3 shots from
heavy long barrel NEF nearly into same hole, at
30yds. Gun locked down. Going about 2200.
Our slow powder loads in 3.5" plastic.
Can be loaded faster.

No tests at long range, bad eyes/no scope, colder
than witches ---, and no time.
I am trying to find who makes these.There are
about 2000 injection mold companies in US.Ed

 
#24 ·
Another 12ga sabot idea, first picture is a 570 gr USS slug,
with Powder Cup seal from BPI, locked to USS discarding sabot
section. This shortens column so that we can get more of the
slower powders in we use, in shorter 2.75" cases. With slower
powders, they get to peak pressure a little easier
so that the cushion usually between seal and sabot/slugs
isn't needed. This locked on seal will aid in smoothbore
accuracy and it will work of course in rifled barrels.
This sabot has a peg on the back that locks it in original
setup to the green USS cushion base/seal, and we just pried
it apart and drilled tight hole to match in the Powder Cup
seal, and forced it on for a locked fit..
Slug is .629" diameter.



Next picture is 3 sizes of first USS sabot slugs, with
the locked on bases which work good with them. Giving
nearly rifle accurracy in smooth bores.



Here is old time picture of couple of Rodda 4 bores.
Man what nice old guns.



Next picture is a 1.5" Minie ball slug, might work for
close to a one gauge. It is next to older 37mm case which
might fire it also. Maybe a way to make a one gauge of
sorts, if.......I get enough ambition...Ed

 
#25 ·
Some more 12ga sabot work. The sabots in first picture are
like ones we want to get made for reloading.
They have 440gr Dixie Gunworks muzzleloading minie slug.
I related earlier that 3 shots with these in heavy rifled
barrel NEF got them all in nearly the same hole, at 30 yds.
Also 4 shots same distance, a 3 inch best group, smooth barrel.
The slight hollow base helps with smooth barrel. The hollow
base isn't as deep say as a 12ga foster slug.Another one they
have, a little heavier, with little deeper hollow base should
make tighter group. Loads in 3.5" plastic going about 2200.



Second picture shows something new I found out.It shows two
different wad setups. When I took the REM Accutip loads apart
I notice they used a thick seal, old style white felt cushion.
All the tests I read about that factory load, says it is always
near the top in accuracy. I had used the BPGS and flexseal
cushion mostly, as it seals real good. But in the smoothbore
test above the thick seal and felt wad gave the 3" group and
the other wad setup 5". The smoothbore, which isn't a perfect
system, for slugs not designed for smooth, worked out to show
and magnify difference between the two wad setups..

What first clued me in on this, to make a check, was recent
weeks research on net,on all sabot patents, where I read that
sometimes plastic cushions cock a little affecting accuracy.
That is the plastic cushions with a lot of space in them.
Where the felt/fiber cushions stay much more stable for a bigger
percentage of shots.The very accurate Hornady SST sabot has no
cushion at all between seal and sabot, but a thin rubber cushion
disc inside their sabot, and the above may be one reason.
The Federal Fusion sabots and the Federal Expander sabot
both are accurate--they don't have a wide open plastic cushion.



Third picture is of a Greener Martini slug gun a guy rigged up
with a heavy rifled bull barrel in 12ga. Great looking gun.



Finally thoughts about all of our posts on many forums(110)
around the net. We are very happy with the response and help
we get doing this. We feel this thread a positive boon and help
to shooters interested in big bores, and by venturing into
the big bore areas will promote more guys getting into shooting,
reloading, smithing, etc. And a measure of interest are the views.
All sites including a big picture site, have about 9 million views.
And also we congratulate the 24hr Campfire Big Bore as being
being the first with our regular 12ga FH thread to go
over 200,000 views.Next is the Highroad with nearly 150,000,
third is the Firingline with nearly 125,000, 4th Accurate
Reloading 112,000, and 5th WeaponsForum 106,000.ED
 
#26 ·
Some possibilities with the 12ga sabots we have been
looking at. We may have possible leads on companies that
can make sabots, that have most of equipment to do so.
If they work out ok, the startup cost isn't as
high as others who have to set up complete machines.
We are working to line up a dealer who will get good ones
made, at one of these sabot making companies.WE hope to
have similiar design as the ones pictured below
but with slightly thicker base. I've sent these sabots
with Dixie cast slugs to different companies to show
what is needed, and what the full size specs should be.
With Dixie cast in they are similiar to Federal
Fusion sabots with lead slugs, only our slugs are 58cal.
We will keep you informed on what happens. At least 5
58cal slugs that Dixie has, looks maybe to work in these,
as best I can tell. And there are a few molds for
58cal cast slugs, by different companies.
The possibilities are, to reload with decent price slugs
and simple inexpensive sabot like these, for buck a round.
40-60 cent slug, 15-20 cent sabot, powder/primer 30 cents.



Those sabots I pictured above we been testing, had 385gr
Remington plastic nose bullets. I used some in my
585HE and I get them to 3900 fps. Just to see how
fast was possible in the 585. If I shot them in
my biggest 585, the 585 HSM, they'd go about 4500 or so.
They are real light compared to 750gr 585 cal bullets.
Like a varmint round. Do up a coyote fine.All skinned.



Some neat guns-First is a 20ga smooth bore Beretta style
break action 20ga. This is one of the greatest style
break actions there is. Beretta made their trap guns on
actions like this and great value for no more
than they cost. This one only 100 bucks.
We lengthened chamber to 3.5" so it can
use various 20ga smoothbore slug loads that we are
working on and testing..The SPW, Hastings, Lightfield
type 20ga slugs have decent 50yd accuracy in heavier
smooth barrels.



Next is couple of older guns I found pictures of,
a 4bore Hughes and a 600NE Wilke. I like them.
2nd is special 20ga double that poster Nitro 450 Express
on the NitroExpress forum had built. Great job
on nice looking slug gun.Ed



 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top